$0.00
View All
Use for venting listed natural gas or liquid propane Category I, draft hood appliances, or appliances that have been specifically tested and listed to use Type B Gas Vent. The appliances listed typically use Type B Gas Vent systems, but not always: Furnaces, Water Heaters, Boilers, Room Heaters, Decorative Gas Appliances, and Unit Heaters. Designed to be placed within 2" x 4" stud walls (4" and 5" oval pipe). 6" may only be placed in a 2" x 6" O.C. stud space.
Item#: 2591368
x
Item#: 2591372
Item#: 2591376
Item#: 2591380
Use to add length to a straight length of Oval Type B Gas Vent pipe. Adjusts from 4"-10". Requires a 2" overlap.
Item#: 2591384
Use to increase oval vent diameter.
Item#: 2591388
Use to convert from round to oval vent.
Item#: 2591392
Use to convert from oval to round vent.
Item#: 2591397
Offsets obstructions as needed. Not adjustable.
Item#: 2591401
Item#: 2591405
Use to support and center Oval Tee. Use with Oval Tee Cap.
Item#: 2591409
Use to center oval vent in a minimum 16" on-center stud space. Serves as a firestop at the ceiling level. Required in multi-story installations.
Item#: 2591412
Use to attach round pipe to oval pipe. Use for a 90° offset or to combine connectors from two or more appliances into a common vent.
Item#: 2591418
Use to attach round pipe to oval pipe. Use for a 90° offset or to combine connectors from two or more appliances into a common vent. Shorter snout allows installation in tight spaces.
Item#: 2591422
Use to close off bottom of Oval Tee. Fits on inner liner.
Item#: 2591428
Use to maintain a weather tight resistant seal between the pipe and the flashing.
Item#: 2591432
Use to weather proof the penetration of vent pipe throught the roof. Storm Collar required. Select roof flashing based on pitch of roof. For pitches of 0/12-6/12.
Item#: 2591436
Use with corrugated metal or tile roofs. Available in Adjustable Roof Flashing style (0/12-6/12). Made of dead soft aluminum. Refer to Roof Flashing tables for dimensions.
Item#: 2591440
Required where pipe terminates above the roof line. Use for vertical installations only.
Item#: 2591444
Use as a connector system to replace rigid gas vent with a flexible section. DuraConnect II can be used when Type B Gas Vent double-wall connector is required. Not to be enclosed and cannot penetrate through walls, floors, or ceilings. Twist-lock connectors on each end.
Item#: 2591448
Use anywhere a single-wall connector is allowed. Not to be enclosed. Twist-lock connectors on each end. Patented.
Item#: 2591464
Use single-wall increaser to increase vent. Additional sizes available through special order.
Item#: 2591480
Use to attach an appliance to DuraConnect connector pipe.
Item#: 2591489
Use to provide support for offsets and horizontal runs. Recommended every 4' to support vertical common vent. Use also with DuraConnect or DuraConnectc II. Wall Strap legs can be rotated 360° to conceal screw.
Item#: 2591493
Use to support the Type B Gas Vent between 16" to 24" on center joists or rafters. A Firestop Spacer is required.
Item#: 2591497
Use for a 90° offset or to combine connectors from two or more appliances into a common vent.
Item#: 2591501
Attaches smaller pipe to branch and smaller pipe to body. Use for a 90° offset or to combine connectors from two or more appliances into a common vent. Additional sizes available through special order.
Item#: 2591508
Use to cap Standard Tee or Increaser Tee. Remove Tee Cap to inspect the system; clean out debris or collected condensate from the common vent. Fits on outer wall.
Item#: 2591511
Use to combine DuraConnect connectors from two or more appliances into a common vent. Additional sizes available through special order.
Item#: 2591515
Use to combine DuraConnect connectors from two or more appliances. Use to connect single-wall pipe or DuraConnect to common vented Type B Gas Vent.
Item#: 2591521
Item #:
This Item Ships FREE!
$0.00
