Chimney Fans

Solve draft problems caused by design problems caused by design problems, cold starts or unusual fireplaces. The Chimney Champion Auto Drafter Gas/Oil/Boilers - Commerical features a clamshell design for easy service, a patented auxiliary cooling fan for motor protection, backward inclined material handling impeller, speed control, an outdoor rated electrical whip and high temperature black finish.

This Chimney Champion Fan Proving Switch for Gas/Oil Fuels is a safety feature that makes sure your fan is working properly before allowing your fireplace to be turned on. It is a simple switching device that will sense pressure in the duct (air flow). If there is now air flow from the fan because of some blockage or mechanical failure the Chimney Champion Fan Proving Switch for Gas/Oil Fuels will sense it and shut down the fireplace.

The Chimney Champion Interlock Control for Gas/Oil Fuels interlocks mechanical draft and combustion air systems with gas/oil fired heating equipment. This safety feature makes sure that your chimney fan is operable before allowing your fireplace fuel to come to the fireplace and ignite. It can be activated by any heater control signal or by a pressure switch or relay using the 5 VDC Control supplied dry contacts.

The Chimney Champion Interlock Control for Gas/Oil Fuels features:

• Adjustable pre and post purge
• LED status/diagnostic indicators
• Selectable voltage to avoid false triggering by electronic burner controls
• Prover switch check circuit to verify that the fan prover switch is open prior to operation
• A 10-second prover switch delay to eliminate burner start up or wind induced prover switch short cycling
• A 5 VDC Control supplied fan prover signal that isolates the burner load circuit from the prover switch circuit

Solve draft problems caused by design problems, cold starts or unusual fireplaces. The Chimney Champion Auto Drafter Wood/Solid Fuels - Standard features a clamshell design for easy service, a patented auxiliary cooling fan for motor protection, backward inclined material handling impeller, speed control, an outdoor rated electrical whip and high temperature black finish.

This auto drafter comes with a 2-year manufacturer warranty and a 6 month satisfaction guarantee.

To determine the size you need measure the length and height of your hearth opening. Multiply the length and height to determine the face area opening in square feet (divide square inches by 144 to convert to square feet). If the fireplace is open on the side or back, total all openings to arrive at the total face area.

Auto Drafter Features:

• For tile lined chimney this clamps to rectangular tile liners 6" x 6" through 10" x 14" and round tile liners from 6"-11"
• For metal vents it fits vent pipes as small as 8" in diameter and as large as 12" outer diameter
• Patented auxiliary fan-automatically turns on if gets to hot
• Adjustable 250-750 CFM

Maintenance: The auto drafter is designed for continuous use. The motor is equipped with permanently lubricated sealed ball bearings which do not require oiling. A vent pipe inspecation must be performed annually. The inspection should include checking all vent pipe and connections blockage and leaks. A safety interlock test must also be performed on the Gas/Oil Fuel models.For gas applications no regular maintenance is required. For solid fuel models inspec impeller after 3 mo nths and set periodic inspecation and cleaning as necessary.

Are you having incurable draft problems? Look no further for a solution than our Enervex Fan. Available in four sizes to fit most chimneys, our Enervex Fan mounts outside the chimney, where it literally sucks the smoke from the flue.

Solve draft problems caused by design problems caused by design problems, cold starts or unusual fireplaces. The Chimney Champion Auto Drafter Wood/Solid Fuels - Large features a clamshell design for easy service, a patented auxiliary cooling fan for motor protection, backward inclined material handling impeller, speed control, an outdoor rated electrical whip and high temperature black finish.

This auto drafter comes with a 2-year manufacturer warranty and a 6 month satisfaction guarantee.

To determine the size you need measure the length and height of your hearth opening. Multiply the length and height to determine the face area opening in square feet (divide square inches by 144 to convert to square feet). If the fireplace is open on the side or back, total all openings to arrive at the total face area.

Auto Drafter Features:

• For tile lined chimney this clamps to rectangular tile liners 8" x 8" through 12" x 14" and round tile liners from 10"-14"
• For metal vents it fits vent pipes as small as " in diameter and as large as 20" outer diameter
• Patented auxiliary fan-automatically turns on if gets to hot
• Adjustable 750-1500 CFM

Maintenance: The auto drafter is designed for continuous use. The motor is equipped with permanently lubricated sealed ball bearings which do not require oiling. A vent pipe inspecation must be performed annually. The inspection should include checking all vent pipe and connections blockage and leaks. A safety interlock test must also be performed on the Gas/Oil Fuel models.For gas applications no regular maintenance is required. For solid fuel models inspec impeller after 3 mo nths and set periodic inspecation and cleaning as necessary.

Are you having incurable draft problems? Look no further for a solution than our Enervex Fan. Available in four sizes to fit most chimneys, our Exhausto Fan mounts outside the chimney, where it literally sucks the smoke from the flue.

Solve draft problems caused by design problems, cold starts or unusual fireplaces. The Chimney Champion Auto Drafter Gas/Oil Fuels - Standard features a clamshell design for easy service, a patented auxiliary cooling fan for motor protection, backward inclined material handling impeller, speed control, an outdoor rated electrical whip and high temperature black finish.

This auto drafter comes with a 2-year manufacturer warranty and a 6 month satisfaction guarantee.

This drafter comes with an Interlock Control to meet all codes. The control features adjustable pre and post purge, LED status/diagnostic indicators, 10 second prover switch delay to avoid burner start up and wind induced short cycling. It interlocks with any 24-120 VAC burner control circuit and also includes “dry” contact actuation option. It's selectable voltage eliminates false activation by burner control circuits. After each burner cycle the control will continue to operate in post-purge mode to allow the venter to purge the heater and vent of residual flue gases. A factory post-purge time is set at 2 minutes and is adjustable up to 16 minutes.

To determine the size you need measure the length and height of your hearth opening. Multiply the length and height to determine the face area opening in square feet (divide square inches by 144 to convert to square feet). If the fireplace is open on the side or back, total all openings to arrive at the total face area.

Auto Drafter Features:

• For tile lined chimney this clamps to rectangular tile liners 6" x 6" through 10" x 14" and round tile liners from 6"-11"
• For metal vents it fits vent pipes as small as 8" in diameter and as large as 12" outer diameter
• Patented auxiliary fan-automatically turns on if gets to hot
• Adjustable 250-750 CFM

Maintenance: The auto drafter is designed for continuous use. The motor is equipped with permanently lubricated sealed ball bearings which do not require oiling. A vent pipe inspecation must be performed annually. The inspection should include checking all vent pipe and connections blockage and leaks. A safety interlock test must also be performed on the Gas/Oil Fuel models.For gas applications no regular maintenance is required. For solid fuel models inspec impeller after 3 mo nths and set periodic inspecation and cleaning as necessary.

Are you having incurable draft problems? Look no further for a solution than our Enervex Fan. Available in four sizes to fit most chimneys, our Exhausto Fan mounts outside the chimney, where it literally sucks the smoke from the flue.

Solve draft problems caused by design problems caused by design problems, cold starts or unusual fireplaces. The Chimney Champion Auto Drafter Gas/Oil Fuels - Large features a clamshell design for easy service, a patented auxiliary cooling fan for motor protection, backward inclined material handling impeller, speed control, an outdoor rated electrical whip and high temperature black finish.

This auto drafter comes with a 2-year manufacturer warranty and a 6 month satisfaction guarantee.

This drafter comes with an Interlock Control to meet all codes. The control features adjustable pre and post purge, LED status/diagnostic indicators, 10 second prover switch delay to avoid burner start up and wind induced short cycling. It interlocks with any 24-120 VAC burner control circuit and also includes “dry” contact actuation option. It's selectable voltage eliminates false activation by burner control circuits. After each burner cycle the control will continue to operate in post-purge mode to allow the venter to purge the heater and vent of residual flue gases. A factory post-purge time is set at 2 minutes and is adjustable up to 16 minutes.

To determine the size you need measure the length and height of your hearth opening. Multiply the length and height to determine the face area opening in square feet (divide square inches by 144 to convert to square feet). If the fireplace is open on the side or back, total all openings to arrive at the total face area.

For tile lined chimney this clamps to rectangular tile liners 8" x 8" through 12" x 14" and round tile liners from 10"-14". For metal vents it fits vent pipes as small as " in diameter and as large as 20" outer diameter.

Auto Drafter Features:

• For tile lined chimney this clamps to rectangular tile liners 6" x 6" through 10" x 14" and round tile liners from 6"-11"
• For metal vents it fits vent pipes as small as 8" in diameter and as large as 12" outer diameter
• Patented auxiliary fan-automatically turns on if gets to hot
• Adjustable 750-1500 CFM

Maintenance: The auto drafter is designed for continuous use. The motor is equipped with permanently lubricated sealed ball bearings which do not require oiling. A vent pipe inspecation must be performed annually. The inspection should include checking all vent pipe and connections blockage and leaks. A safety interlock test must also be performed on the Gas/Oil Fuel models.For gas applications no regular maintenance is required. For solid fuel models inspec impeller after 3 mo nths and set periodic inspecation and cleaning as necessary.

Are you having incurable draft problems? Look no further for a solution than our Enervex Fan. Available in four sizes to fit most chimneys, our Enervex Fan mounts outside the chimney, where it literally sucks the smoke from the flue.