$0.00
View All
Use to join flex liner sections together.
DirectVent is an unitized, coaxial venting system designed for use with direct vent gas or propane stoves, heaters and fireplaces. The features include tight inner connections for superb performance , with no gaskets or sealant required (unless specified by appliance manufacturer).
Item#: 2590956
x
Use only in accordance with specific appliance manufacturer's installation instructions to restrict incoming combustion air.
Item#: 2590891
Use to maintain a weather tight resistant seal between the pipe and the flashing.
Item#: 2590909
Required for multi-story vertical installations at the second floor and any subsequent floors. 4" x 6 5/8" style may vary.
Item#: 2590882
Use for supporting vent pipe between offsets.
Item#: 2590841
Use to support vent pipe. Provides 1" clearance. Recommend installing Wall Straps at 4-foot intervals on vertical runs.
Item#: 2590888
Use to add length to a straight length of DirectVent Pro. 8 1/2" pipe adds 3"-7" of length, 16" pipe adds 3"-14 1/2" of length, when used with rigid sections of pipe. DirectVent lengths feature a fully unitized, twist-lock construction. Use of sealant is optional, unless specified by the appliance manufacturer. Also available in black (both feature laser-welded outer wall seams). Does not fit DirectVent GS pipe.
Item#: 2590819
Designed for appliances tested and listed for DirectVent. Features a fully unitized twist-lock construction in both 4" x 6 5/8" and 5" x 8" vent sizes. Use of sealant is optional, unless specified by the appliance manufacturer. To calculate install length, subtract 1 1/2" for each joint. No beads or hems. Black pipe lengths feature exterior laser-welded seams.
Item#: 2590785
Use to weatherproof the pentration of vent pipe through the roof. Storm Collar required. Select roof flashing based on pitch of the roof. For pitches of 0/12 - 6/12.
Item#: 2590894
Use as a flex connector with inserts with 3" co-linear intake and exhaust ports.
Item#: 2590975
Provides a complete wall-pass-through and interior firestop. Features an adjustable sleeve for an exact fit. Eliminates visible trim on exterior or wall near cap. Sized to fit all DirectVent Pro termination caps.
Item#: 2590856
Prevents water intrusion into stucco-sided homes. Allows the installer to apply siding material (i.e.: stucco, brick, etc) over the flanges up to the sides of the flashing for a water-tight seal. Kit includes 4 pieces; sized for 4" x 6 5/8" Sconce Cap and Round Horizontal Cap only.
Item#: 2592248
Use to add length to a straight length of DirectVent Pro. 8 1/2" pipe adds 3"-7" of length, 16" pipe adds 3"-14 1/2" of length, when used with rigid sections of pipe. DirectVent lengths feature a fully unitized, twist-lock construction. Use of sealant is optional, unless specified by the appliance manufacturer. Also available in galvalume (both feature laser-welded outer wall seams). Does not fit DirectVent GS pipe.
Item#: 2590824
Use as a heat shield on structures with vinyl siding, or other temperature sensitive materials, to help prevent warping and/or melting of the material. Use only on horizontal terminations and on any irregular surfaced siding (i.e.: ship lap siding, shake shingle siding) so cap is not embedded in the siding. Kit includes 4 pieces; sized for Sconce Cap and Round Horizontal Cap only.
Item#: 2590872
Provides a complete wall-pass-through and firestop. Use with Round Horizontal Cap and Sconce Cap only. May be required in Canada. Refer to the appliance manufacturer's installation instructions for requirements.
Item#: 2590853
Item#: 2590802
Use as a heat shield on structures with vinyl siding, or other temperature sensitive materials, to help prevent warping and/or melting of the material. Use only on horizontal terminations and on any irregular surfaced siding (i.e.: ship lap siding, shake shingle siding) so cap is not embedded in the siding. Kit includes 4 pieces; sized for Square Horizontal Cap only.
Item#: 2590865
Used to offset obstructions as needed. Fully unitized, twist-lock construction. Elbows swivel, allowing the lock to remain fully engaged while aligning to the desired direction. The angle will remain fixed at 45°.
Item#: 2590829
Provides a complete wall-pass-through and firestop. Use with Square Horizontal Cap only. May be required in Canada. Refer to the appliance manufacturer's installation instructions for requirements.
Item#: 2590850
For horizontal (through-wall) installations. Refer to the appliance manufacturer's installation instructions for requirements.
Item#: 2590859
Attaches to appliance outlet allowing pipe to easily connect or disconnect. For Vermont Castings appliances.
Item#: 2590974
Use to weatherproof the pentration of vent pipe through the roof. Storm Collar required. Use on flat roofs, chase enclosures, or masonry chimney.
Item#: 2590900
Used to offset obstructions as needed. Fully unitized, twist-lock construction. Elbows swivel, allowing the lock to remain fully engaged while aligning to the desired direction. The angle will remain fixed at 90°.
Item#: 2590835
Prevents water intrusion into stucco-sided homes. Allows the installer to apply siding material (i.e.: stucco, brick, etc) over the flanges up to the sides of the flashing for a water-tight seal. Kit includes 4 pieces; sized for Square Horizontal Cap only.
Item#: 2590876
Use as a decorative cover for horizontal (through-wall) installations or for flat ceiling installations. Fits over the Wall Thimble face plate. Comes with an insulation ring to reduce air infiltration where the pipe slips through the thimble.
Item#: 2590844
Item#: 2590832
Use as a heat shield on structures with vinyl siding, or other temperature sensitive materials, to help prevent warping and/or melting of the material. Use only on horizontal terminations and on any irregular surfaced siding (i.e.: ship lap siding, shake shingle siding) so cap is not embedded in the siding. Sized for Square Horizontal Cap.
Item#: 2590862
Use with corrugated metal or tile roofs. Available in sizes 4" x 6 5/8" and 5" x 8". Made of dead soft aluminum.
Item#: 2590903
Use to weatherproof the penetration of vent pipe through the roof. Storm Collar required. Select roof flashing based on pitch of the roof. For use with 4" x 6-5/8" and 5" x 8".
Item#: 2590897
Item#: 2590838
Use for horizontal through-the-wall terminations. Provides improved performance in high wind conditions. For vertical terminations only.
Item#: 2590942
Required for installations that pass through an attic to prevent insulation and debris from accumulating near the vent. Provides 1" clearance to combustibles.
Item#: 2590885
Use for vertical terminations only. Check the appliance manufacturer's instructions to determine which caps are approved for use with their appliance.
Item#: 2590945
Item#: 2590906
Kit includes Cap Adapter and 18" x 18" Flashing. Kit is for 4" x6 5/8" DirectVent. Termination Cap and 4" Flex are sold separately.
Use existing masonry chimney. Route the exhaust gases and intake air through the side of the masonry chimney.
Item#: 2590967
Use to pass through ceiling and support pipe. May be used on vaulted or flat ceilings. Trim and clamp included.
Item#: 2590847
Use for through-the-wall terminations. Check installation instructions for restrictions on horizontal cap terminations, such as minimum distance from windows and doors. Check with appliance manufacturer for approval.
Item#: 2590912
Use 3" flex with the co-linear system and 4" flex with Conversion Kits.
Item#: 2590953
Use with through-the-wall termination cap where high winds are present. Also use as a safety heat shield to prevent children or others from coming into contact with the vent termination cap. Fits both 4" x 6 5/8" and 5" x 8" terminations.
Item#: 2590973
Use for through-the-wall terminations. Provides improved performance in high wind conditions. Check installation instructions for restrictions on horizontal cap terminations, such as minimum distance from windows and doors. Check with appliance manufacturer for approval. Patented.
Item#: 2590922
Use for through-the-wall terminations. Check installation instructions for restrictions on horizontal cap terminations, such as minimum distance from windows and doors. Check with appliance manufacturer for approval. Patented.
Item#: 2590915
Use Co-Linear Adapter for stoves with 4" x 6 5/8" co-axial outlets. Refer to appliance manufacturer's installatio instructions for approval. Uses 3" aluminum flex for both intake and exhaust.
Item#: 2590959
Kit includes Termination Connector and Flashing. DirectVent Pro 4" x 6 5/8" Termination Caps, 3" Flex, and Co-Linear Flex Connectors are sold separately.
DirectVent Pro chimney liner termination kit must be tested and listed for each appliance. Refer to stove manufacturer's installation instructions.
Item#: 2590965
Use in extremely cold climates. Similar to the Low Profile Termination Cap but taller in overall height to separate the ari intake vents from the exhaust area. Refer to the appliance manufacturer's installation instructions for requirements.
Item#: 2590950
Use for standard and high-wind through-the-wall terminations. Check installation instructions for restrictions on horizontal cap terminations, such as minimum distance from windows and doors.
Item#: 2590929
Kit includes Cap Adapter and a Retro Connector. DirectVent Pro 4" x 6 5/8" Termination Cap and 4" Flex are sold separately.
Use with 4" x 6 5/8" DirectVent gas stoves. Use existing through-the-ceiling, wood-stove metal chimney. Route the exhaust gases and intake air through the existing wood-stove metal chimney.
Item#: 2590970
Item#: 2590969
Item#: 2590971
Item #:
This Item Ships FREE!
$0.00
